How to Fix Hoverboard’s Wheel, Battery & Foot Sensor

The worst moment for a hoverboard to break down is on a night out with friends. Relax, you can still go out since fixing the problem will just take a few minutes. Fix your hoverboard’s wheel, battery, and foot sensor using this guide. So, if you follow these procedures carefully, the issue will be resolved.

Hoverboard Wheel, Battery, and Foot Sensor Repair

Whether or not any of these issues need expert help depends on the severity of the situation. Normal wear and tear is easily repaired. However, component failure or more catastrophic damage needs expert assistance.

Fixing Hoverboard Locked Wheel

A hoverboard’s safety feature is a locked wheel. This is a regular problem for a new hoverboard user. The locking mechanism avoids unneeded motions that might pose dangers. But the solution is easy.

Simply hit the unlock button on the hoverboard’s control. And now your hoverboard is ready. After each ride, lock your hoverboard. This prevents your hoverboard from doing unexpected motions when you stand on it. The lock mechanism also prevents theft of your hoverboard.

Repair Squeaky Wheel Hoverboard Rubbing

Squeaky wheels may ruin a pleasant ride. To eliminate clicking noises, tighten the nuts and screws periodically. But it’s not the only cause of loud wheels. A defective hoverboard motor or engine may cause a noisy wheel.

Wheel rubbing occurs when the space between the wheel and guard is too near or too distant. The solutions are straightforward but need tremendous caution. To begin, turn on the hoverboard and mark the stuck wheel.

Next, dismantle your hoverboard by flipping it over a foam or box. It provides steadiness. Remove the clip that connects the light to the guard for simple removal. On the side of the wheel is a 2″ X 4″ black box known as a circuit box.

Unclip the wires from the circuit box. Place the plastic shell on the hoverboard’s side. Above the circuit box is a wheel-assist clamp with four screws. To remove the Philip head screws, use a screwdriver. Unclasp the circuit box cables. Remove and store the circuit box.

The next step is to release the 6mm square metal fasteners. An Allen wrench may be used to release the four major bolts. This allows you to move the wheel outward and upward. If the wheel is locked and cannot move, use a hammer to gently tap the metal piece to free it.

Ensure that the wheel does not rub and moves smoothly. Once the wheel movement is satisfactory, reconnect the cables to the black box. Reassemble the hoverboard by tightening the bolts with the Allen wrench.

Fixing Non-Functioning Wheel Of Hoverboard

If your hoverboard’s wheel isn’t operating, check for any loose wires. The hoverboard is made up of computer chips, a battery, and cables. A loose wire often causes the wheel to be unable to operate.

A hoverboard loses equilibrium due to loose cables. So, if your hoverboard wheel is acting up, check for loose wiring. To do so, use a Phillips head screwdriver to open your hoverboard. Next, keep an eye out for any disconnected, exposed, or damaged wires.

Gyroscope Upgrade

The hoverboard’s gyroscope technology lets the wheel to rotate in multiple directions. The defective gyroscope causes trouble keeping equilibrium on a hoverboard wheel. The gyroscope is sideways. Remember that finding a problem and solving it are two separate things.

Previously, getting an identical gyroscope was simple due to the small number of circuit board makers. Finding a matching gyroscope is vital. Finding an identical match fixes the balance problem. However, several businesses now make hoverboard circuit boards, making it difficult.

Finding an identical gyroscope takes time and effort. It is advised not to replace an outdated gyroscope owing to the high possibility of discovering a nonidentical match that may produce complications such as fire or smoke.

How To Replace A Circuit Board Or A Wheel

Replacing damaged hoverboard components with identical matches is a time-consuming and risky process. The safest approach is to replace the hoverboard’s circuit board. Make that the new circuit board has the same configuration as the old one. A lot of circuit board replacement kits have differences.

Installing a new circuit board kit may create compatibility concerns. Verify the kit’s compatibility with the hoverboard’s year of manufacture. Or you may compare the kits to the hoverboard’s circuit board. Replacing a gyroscope or circuit board does not help.

Then you must replace the hoverboard’s side wheel that is out of balance. However, the wheel you replace must be compatible with the hoverboard. Sadly, the variety of wheel sizes and kinds produced by various businesses has made this problematic. So, before ordering or buying a new wheel, double verify the size and kind.

Why Do Batteries Fail?

Aside from the wheel, a hoverboard’s poor performance may be due to battery issues. To determine whether the battery is defective, it must first be tested. The red hue indicates that your hoverboard’s battery is charging. This also ensures the battery and charger work properly.

However, if the battery is green, that means it is fully charged. Or you’ve been charging the battery but it’s not charging. The hoverboard’s battery or charger is faulty. Also, even after full charge, the battery exhibits a red light, indicating low battery symptoms.

Diagnosis

REMEMBER: You CANNOT REPAIR A HOVERBOARD BAT It’s a technical job that demands expert help. However, you can easily change a hoverboard battery by yourself. Changing a battery requires no special equipment. A Phillips screwdriver is all you need.

The battery is on the other side of the charging port, so first open the side of your hoverboard. Opening the hoverboard reveals the battery cage. To get to the battery, loosen the cage’s four bolts. Then unhook the motherboard’s connections from the battery.

Install a new battery, reconnect the connection, and connect the battery to the motherboard. Then fasten the battery cage with bolts. The final step is to screw the jacket on the hoverboard and you are ready to go. Finally, completely charge your hoverboard to verify the battery. 

Charger issue

When charging your hoverboard, the issue isn’t necessarily the battery. The issue may be with the charger or its socket. It is easy to verify or find the problem’s origins. First, connect the charger to the hoverboard and the wall. If the charger and hoverboard both light up, they work well. If the hoverboard does not react to the charger, the charger is malfunctioning.

The problem isn’t with the battery or hoverboard. The charger usually becomes hot when plugged in and stays hot when charging the hoverboard. A problem may exist if the charger becomes hot after being plugged in. Replace the malfunctioning charger with a new one compatible with your hoverboard.

Fixing Foot Sensor Issues

Pads stuck

When the foot sensor does not identify the rider, the pads jam. Keep cool while dealing with clogged pads and follow these steps: turn off hoverboard Then replace the pads. This will enable the sensors to detect the rider. If you are still encountering the same difficulty, then the fault is definitely contained within the hoverboard. Open the hoverboard and adjust the pads. This should help.

Sensor Replacement

A pressure sensor detects a rider on the board. If the pressure sensor does not detect you, it is time to replace it. First, open the lid to reveal the sensor near the wheel. Then swap the new and old sensors.

When you stand on the board, the pads detect you because the sensor wings connect when you stand on them. That is the functioning mechanism of the pressure sensor. If a pressure sensor cannot fulfill this duty, it must be replaced. 

How To Fix Shaking And Vibrating

Who doesn’t desire a smooth ride, but the hoverboard may start spinning or trembling as you put your feet on it. What occurs when the air pad gets clogged. When you push the pads, they will vibrate. You must resolve this. If not, you may forget about riding a hoverboard smoothly.

How to repair it. Stop the hoverboard. Turn the back cover over. Test with your hand to see whether the issue is localized. Opening the rear cover reveals a plastic bag. Locate the plastic bag’s tiny lips and cut a small hole to let the trapped air out.

Restore everything to its original location. Next, turn on the hoverboard and enjoy the ride. Be careful not to damage the other pieces or the plastic bag while releasing air. A sharp pen may be used to puncture a plastic bag. No need to remove every component to get to the target region.

Conclusion

This was a lengthy review of repairing the hoverboard’s wheel, battery, and foot sensor. The aforementioned steps are easy to follow and may be done by anybody.

Other Post:

How tight should longboard wheels be?