How To Clean Lawn Mower Gas Tank?

The primary function of the fuel tanks on lawnmowers is to store gas, but these tanks are also critical for maintaining the fuel in your engine in a clean, secure, and vented condition. It is possible that your lawnmower will not start when you attempt to begin mowing your lawn if it has been unused for an extended period of time. This happens primarily because there is some fuel still present in the tank after use. But also debris, old fuel, or condensation may result in a blocked fuel line. If you notice dust or debris in the gas tank, or even worse, gas is leaking, the vehicle has a problem. It is time to perform maintenance on the fuel tank.

How to clean a lawnmower gas tank:

  • Step 1: Examine the spark plug
  • Step 2: Drain the tank
  • Step 3: Clean the carburetor
  • Step 4: Rinse the tank
  • Step 5: Check the fuel filter for deposits or debris.
  • Step 6: Install a new tank if needed

The primary function of a fuel tank is to transport and store sufficient fuel while also maintaining its cleanliness and guarding against its degradation. Clean and free of debris are critical for a carburetor’s tiny channels. If your lawnmower’s gas tank is neglected, it will eventually stop working, so remove the fuel and clean the tank first. You’ll find all the information you need right here.

Steps To Clean a Lawnmower Gas Tank:

If you want your lawnmower to operate efficiently, follow these steps to clean it yourself so you don’t have to call a professional. We have provided clear, concise, and understandable instructions for each step in the process.

● Step 1. Examining the spark plug:

There are few things more critical to a gas tank’s operation than the spark plug. Engine operation depends on the proper ignition of the air-fuel mixture by a spark plug. An electric arc is formed between the two leads of the plug, which eventually results in the spark. Carbon buildup can have an impact on spark generation over time. Additionally, wear and tear can weaken the electrode.

– Inspection of the spark plug:

Inspecting the plug for damage or wear and tear should help you check if the component is working or not. You should check if there is a considerable carbon buildup or if any electrode is broken or not.

– Ignition tester:

To check if the plug is producing the spark, you can use an ignition tester. The tester’s terminals will show a vital spark indicating that the component is working correctly. No spark means that the plug is defective and must be replaced.

– Replacing the plug:

A spark plug that is broken beyond repair cannot be fixed. Spark plugs are relatively inexpensive replacement parts that can make a significant impact on how an engine performs. It is recommended that you recondition your spark plug at least once per year as a general rule.

When you clean the tank of the lawnmower, there may be some vapors left over that are sufficient to start the engine and rotate the blade. This is just an additional precaution to take, but in case it happens, you should try starting the engine before rotating the blade. It is not recommended to clean the mower with the spark plug still attached.

● Step 2. Drain the tank:

Before you get down to business, make sure the gas container is in working order. At this point, you will need to detach the fuel line that is attached to the carburetor. Place the gas container in the space below the tank, then pour out the gas. When the tank is empty, use the flashlight to inspect it for any debris or beads of light that might indicate cracks or holes. To clear away loose debris, you can use a baster. If you discover any damage, the original equipment from the manufacturer should be used to repair or replace the tank.

● Step 3. Clean the carburetor:

The carburetor is an essential part of the engine that plays an important role in ensuring that the appropriate proportions of air and fuel are delivered to the combustion chamber. The clogging may cause the pipes to thin out, which will result in an inadequate supply of fuel. In the worst possible scenarios, the power output of the engine drops dramatically, and it begins to make a gurgling sound.

– Steps to clean the carburetor: 

  • Step 1: Remove the outer casing of the engine.
  • Step 2: Check Air Filters and their housing.
  • Step 3: Unbolt the carburetor and remove it from the fuel line.
  • Step 4: Unbolt the bowl and clean the nuts.
  • Step 5: Replace the central gasket.
  • Step 6: Replace the needle.
  • Step 7: Check All Connections.
  • Step 8: Use Carnuretor Cleaner
  • Step 9: Reassemble and reattach.

– Preventive maintenance:

To enhance the lifetime of your lawnmower and to make sure that your machine will start without problems, it is wise to do some preventive maintenance

  • Fresh fuel: To ensure better performance and effectiveness of the carburetor, it is recommended that you should always use new gas for your mower. Gas will go bad after a few months.
  • Fuel stabilizer: We also recommend that you add a fuel stabilizer in the fuel tank if you plan not to use it for some time so that its quality does not deteriorate.
  • Carburetorcleaner: Carefully spray carb cleaner into the intake hole from where the fuel goes into the carburetor. Spray the cleaner into the outtake hole and spray thoroughly in the inner part of the tank. With all the grass, twigs, and debris, the need for the hour is to use a carburetor cleaner to clear out all the deposits within the carburetor, as these deposits can congest the passage of both air and fuel decrease the efficiency, thus stop the engine altogether.
  • Carburetor repair kit: You can also purchase a carburetor repair kit to help you repair and replace the defective parts.

● Step 4. Rinse the tank:

You should never clean the tank with water. Carburetors and fuel injectors are susceptible to damage when exposed to residual water. You could also try rinsing the tank with a small amount of gas as an alternative. Now put the lid back on the tank and give it a good shake to ensure that the gas gets into every crevice of the tank. Take some of this used gas and put it in the rusty gas can. As a result of the fact that this used gas will clog or otherwise damage other engines, it was determined that it could not be used in those engines. Get rid of all of the stale and unused fuel in a secure manner.

● Step 5. Examine the fuel filter for dust and deposits:

The filter, whether it be for the oil or the fuel, acts as the last line of defense before the fuel enters the combustion process. The filter, as its name suggests, is responsible for preventing impurities, dirt, and harmful objects like insects and residues from passing through while allowing only the fuel to do so. In the event that contaminated fuel comes into contact with the filter, it is possible that the filter will become clogged well before the typical end of its useful life. As a result of all of this, the engine action becomes choppy, which causes cranking problems.

  • Clean fuel: It is always preferable to use clean fuel with fuel stabilizers when the pressure has to be used. Extra fuel in the tank will always cause problems.
  • Replacement: Like all filters, fuel filters should be replaced annually unless the black residue is visible to the naked eye.

● Step 6. Reattach the fuel tank:

If you are mounting a new fuel tank or reattaching an older one, be sure to tighten the cap screws very tightly. It is time to replace the fuel line and the filter at this point. Under no circumstances should you attempt to refurbish a damaged tank. It is prone to leaks, which could result in fuel contamination or a fire. A vented gas cap is used on many tanks so that there is always a pressure difference between the outside environment and the fuel system. A backup cap that is properly installed and secured can fix the problem if the fuel is leaking.

Additional Precautionary measures:

Before starting, operating, or servicing your engine, always read the engine and equipment manual or equipment to prevent property damage or personal injury.

  • Fuel and the fumes of fuel are exceptionally explosive and inflammable. Try to handle fuel with care.
  • Fuel tanks should be made of material corrosion-resistant or glazed with a corrosion-resilient substance to withstand against harmful effects of alcohol, water, or salt. The tank should be replaced if it is damaged or corroded. Use only recommended parts by the engine manufacturer if you are attempting to change the tank.
  • Some engines like those used on walk-behind mowers use a fuel filter placed inside the fuel outlet tank. These cannot be replaced – consult your local dealers on how to service in-tank filters. A filter may also be located outside the tank, midway along the fuel line.

Frequently asked questions:

1. How do you flush out a gas tank?

Take fuel pump out of tank and put it aside (prevent residual debris from falling into the tank). After inserting the hose into the fuel tank, begin slowly pouring clean, hot water into the container. Spray some mild detergent into the tank as it is being filled with water. Use a brush to clean the debris off the sides of the tank if opening the lid allows you to do so.

2. How do you clean a metal gas tank?

A suitable cleaning solvent is acetone because of its affinity to vaporize quickly. The cleaner will help to clean the interior of the tank free of no matter what would stick. Close the cap of the tank, and then agitate it thoroughly before pouring out the solvent.

Steps to follow:

  • Step 1: Draw off any gas inside the tank into a container, which is safe to use.
  • Step 2: Detach the fuel lines running from the tank to the engine.
  • Step 3: Remove the fuel source from the top of the tank by rotating it anticlockwise until it breaks free.
  • Step 4: Wash the tank with a garden hose.
  • Step 5: Put on rubber gloves and eye protection.

3. How do you keep a gas tank from rusting after cleaning?

After that, you acid clean it, rinse it with baking soda water mixture, then use soap water for final cleansing, then put a little diesel fuel and splash it around, the fuel will coat inside of the tank and prevent it from flash rusting, then as you pass gas through it. It will create a light oily coating on it.

4. How do you get rust out of a metal gas tank?

Vinegar contains acetic acid that is used to clean corrosion. This can be done first by filling the tank with water and then draining that. Next, plug the hole and fill the tank with the vinegar, leaving it for a night to dissolve and soften the rust.

Final Remarks:

In the future, you should purchase gas in smaller quantities in order to guarantee that the gas you use is of a high quality. I will deteriorate if the gas remains for a more extended period of time. Only purchase the amount of gasoline that will last you between two and four weeks. Add a fuel stabilizer to your mower’s gas tank if you are going to be away for an extended period of time and letting it sit idle. This will prevent the fuel from becoming contaminated. Open up the throttle as much as you can while you are mowing so that you can assist us in emptying the fuel tank before we put the mower away in the shed. If you do this on a consistent basis, the gas in the tank will not become stale. Old gas deteriorates, which in turn causes damage to rubber lines, tank corrosion, and the production of debris and junk that destroys carburetors.

See more :


Best Worx Lawn Mowers

Best Snapper Lawn Mowers

The best Ryobi lawn mowers